L-com WLKIT-GX/GXI Series Kits User Manual download pdf

OUTDOOR INSTALLATION WARNING

IMPORTANT SAFETY PRECAUTIONS:

LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the equipment

you are installing.

IMPORTANT: Look over the site before beginning any installation, and anticipate possible hazards, especially these:

CONTACTING POWER LINES CAN BE LETHAL. Make sure no power lines are

anywhere where possible contact can be made. Antennas, masts, towers, guy wires or cables

may lean or fall and contact these lines. People may be injured or killed if they are touching or

holding any part of equipment when it contacts electric lines. Make sure there is NO possibility

that equipment or personnel can come in contact directly or indirectly with power lines.

Assume all overhead lines are power lines.

The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total length of the

mast/antenna combination. This will ensure that the mast will not contact power if it falls either during installation or later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.

• Select equipment locations that will allow safe, simple equipment installation.

• Don’t work alone. A friend or co-worker can save your life if an accident happens.

• Use approved non-conducting ladders and other safety equipment. Make sure all equipment is in good repair.

• If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.

• If anything such as a wire or mast does come in contact with a power line,

DON’T TOUCH IT OR ATTEMPT TO

MOVE IT

. Instead, save your life by calling the power company.

• Don’t attempt to erect antennas or towers on windy days.

MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES

CONNECTED TO ANTENNAS HAVE LIGHTNING ARRESTORS.

This will help prevent fire damage or human injury

in case of lightning, static build-up, or short circuit within equipment connected to the antenna.

• The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more

approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.

• Refer to the National Electrical Code for grounding details.

• Lightning arrestors for antenna feed coaxial cables are available from HyperLink Technologies, Inc.

IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:

• DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

• Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical power.

• Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency

medical aid has been requested.

L-COM, INC. 45 BEECHWOOD DRIVE NORTH ANDOVER, MA 01845

WWW.L-COM.COM E-MAIL: SAL[email protected] PHONE: 1-800-343-1455 FAX: 1-978-689-9484

1 2 3 4 5 6 7 8 9 10

Summary of Contents

Page 1 - OUTDOOR INSTALLATION WARNING

OUTDOOR INSTALLATION WARNING IMPORTANT SAFETY PRECAUTIONS:LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that

Page 2

Card Alone1000 800 630 500 400 250 150 (mW) - as labeledAntenna Model Antenna Type Gain (dBi) 29.9 29 28 27 26 24 21.8 17.5 (dBm)HG2401U whip/monopole

Page 3

End-User ManualModel HA2401-XI-325XFCC ID: MYF-XI-325XIC: 2837A- XI-325XInterference StatementThis device complies with Part 15 of the FCC Rules and w

Page 4

Any changes or modifications of equipment not expressly approved by the manufacturer could void the user’s authority to operate the equipment and the

Page 5

When locating the antenna or operating this device you must observe the following exposure limits:When this device is installed either as a fixed-moun

Page 6

PC Card and Software Installation I. Network Configuration XI-325 is an IEEE802.11b-compliant PCMCIA Type II DSSS wireless LAN PC card. It

Page 7 - Utility Information

the Utility icon. Utility interface will then appear and configuration can be accomplished here.IV. Using Utility to Set Up Ad-Hoc NetworkIf wirele

Page 8

would show status for all available access points. By using this tool, it is possible to findout ESSID for the connected wireless group.On the main

Page 9

ESSID Select the wireless network group to join(“ANY” is default setting).Network Type Select the station operation mode,Ad-Hoc: (without Access Point

Page 10

enolA draC)Bd( gnitaR rewoP reifilpmAAntenna Model Gain (dBi)29.9 29 28 27 26 24 21.8 17.5HG2401U 19.9 8.9 8.0 7.1 6.3 5.0 3.9 2.7HG2402RD211.1 10.0

Comments to this Manuals

No comments

L-com WLKIT-GX/GXI Series Kits User Manual

Browse online or download User Manual for Hardware L-com WLKIT-GX/GXI Series Kits. L-com WLKIT-GX/GXI Series Kits User Manual [en] [es]

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware L-com WLKIT-GX/GXI Series Kits